Call or Text: 1-443-716-5556 | Email: info@chimiver.us

Adhesive Elastic – Single Component

$120.00 $120.00

ADESIVER ELASTIC is a single-component hydro-curing prepolymer based adhesive with a silanic termination (MStechnology). Recommended for gluing of pre-finished wooden floor onto marble, grit, ceramic or marble-chip floor tiles, etc. Also suitable for gluing wooden floor onto subfloors with radiant heating.

  • 0% VOC
  • Max Open Time – 1 hour
  • Application Temperature, 55 – 77 Degrees Fahrenheit
  • Oak Colored
  • 33lb. / 15kg. / 2.3 gal
  • Maximum storage is 9 months.
  • 47-83 sq. ft. coverage per gallon
SKU: AESCW-7 Categories:

Description

Adhesive Elastic – Single Component – 2.3 Gallons

ADESIVER ELASTIC is a single-component hydro-curing prepolymer based adhesive with a silanic termination (MS technology). This adhesive is classified as “ELASTIC” according to ISO 17178. Recommended for gluing of pre-finished wooden floor onto marble, grit, ceramic or marble-chip floor tiles, etc. Also suitable for gluing wooden floor onto underfloor heating and cooling system. ADESIVER ELASTIC has very good acoustic insulation characteristics. CERTIFICATES: EC1 PLUS, heat conductivity (CSI test report n° 0013/DC/TTS/19). ADESIVER ELASTIC can contribute to the achievement of QI CREDIT 4.1 according to the parameters of the GEV dated 03 March 2009, because it meets the certification LEED protocol (Leadership in Energy and Environmental Design).

HOW TO USE

Before use, mix the product until it is uniform. The subfloor, according to local regulations, must be dry, free from cracks, uniform and completely clean from the elements that can damage its adherence. Apply ADESIVER ELASTIC paying attention to lay the wood blocks side by side and knock them down well to make sure the adhesive glues well to the entire surface. Perfect adhesion to the subfloor is ensured if at least 65% of each wooden component is in direct contact with the adhesive. The application of a primer usually is not required, if the substrate is problematic (for example: absence of an impermeable layer, fragile surfaces, ignition cycle on radiant heating not carried out, anhydrite substrate, etc.), we recommend the use of a primer in order to improve the characteristics of the substrate. Subfloor with radiant floor heating, where the use of a primer is required, apply one coat of PRYMER SF 1105 (see technical data sheet) and after 24 hours proceed with the application of ADESIVER ELASTIC. If the subfloor is porous or friable, we suggest applying a coat of PRYMER A, PRYMER SF 1105, PRYMER FAST 500, PRYMER PUB 77 or PRYMER 100. The drying time for the subsequent coats depends on the primer used (see technical data sheets). If you need to glue the wooden floor onto glazed subfloors (such as ceramic, enameled tiles or polished marble, etc.)remove and clean the surface from dust, grit, glue and waxes. Apply by cloth the adhesion promoter DILUENTE APA following the correct application time (see technical data sheet), then apply ADESIVER ELASTIC. Sand the surface of anhydrite subfloors thoroughly using 24 or 36 grit sandpaper; remove dust and apply primer using PRYMER SF 1105 (do not dilute) or PRYMER FAST 500 (diluted with 30% of DMC 50). Even PRYMER PUB 77 can be applied on the anhydrite subfloors with DILUENTE DMC 50 in a 70:30 ratio. ADESIVER ELASTIC must be acclimatized at room temperature before being applied. Sand the floor after 3-4 days, depending on the atmospheric conditions and humidity level of the wood species used. The possible excess of glue can be removed with a cleaning humid cloth. In case of left over, seal the bucket properly by using both lids to avoid waste. Note: Do not apply ADESIVER ELASTIC in presence of high evaporative fluxes as they cause the increase of pH of the substrate (pH>=10) and they cause problems with the screed/glue/wood system. In case of doubt apply one coat of PRYMER SF 1105 (see technical data sheet) and after 24 hours proceed with the application of ADESIVER ELASTIC

Adhesive Elastic Data Sheet

Additional information

Weight 22 lbs
Dimensions 10 × 10 × 11 in